10 Tips for Super Cleaning Your Mouse track pad with out damage
If you’re like most people, you probably use your Mouse track pad every day without giving it much thought, until it becomes too dirty to look at. While cleaning your mousepad won’t take long. And there are several common mistakes that could be making it look worse than ever before. In order to make sure your mousepad stays clean and looking nice. So be sure to avoid these 10 common mousepad cleaning mistakes!
1) Mouse track pad Prevent stains
You can protect your Mouse track pad from spills by using a sleeve or protector. If you don’t have one, you can easily make your own from materials found in most homes. Cut open an old pillowcase and lay it flat with one end touching a wall. And another touching a corner of your desk. Place your mouse pad on top of it, so that when you turn it over. There’s about 3/4 inch to 1 inch of pillowcase sticking out beyond where your mouse pad ends. This is where liquid will collect if you spill anything on it. But since there’s more room than before, less of it will stain or leak through onto your computer. (Just be sure to flip it back once you’re done.)
As far as stains go, all you need is water and soap. Don’t use harsh chemicals like bleach or ammonia unless they’re specifically recommended by the manufacturer. Use a soft cloth and rub lightly at first, then scrub harder if needed until stains are gone. Once again, never scrub hard enough to cause damage! When finished, wipe down your mousepad with a damp cloth (again: no bleach. And let dry thoroughly before putting it back into use. And remember: prevention is key.
2) Touchpad clean with hot water
Hot water (or, even better, a good disinfectant) is one of your best weapons when it comes to getting rid of germs and bacteria on your Mouse track pad . Place your pad in a basin filled with water so that it covers most of its surface area, then soak it in there for 10 minutes or so. After that time has passed, you can remove your mouse pad from the water and take a clean cloth to dry off all sides. You should also shake off any excess liquid before putting it back into use. Remember: once you’ve cleaned something with hot water, you have to let it air-dry completely; otherwise, mold will form and cause an even bigger problem! So if you don’t want to keep cleaning your mouse pad regularly, try looking at anti-bacterial sprays instead.
Now spray some cleaner onto your pad’s surface—you can buy special Mouse track pad cleaners if you’d like—and wipe away anything that doesn’t belong there using a lint-free cloth. Repeat as necessary until no more dirt appears on your cloth when wiping down your pad’s surface. If you’re lucky enough to own a mechanical keyboard , make sure not to spray directly onto it; as we mentioned above, hot water is fine for most materials but might damage electronics . If yours does get wet accidentally, just dry it out quickly using another towel or hairdryer.
3) Remove gross crusty things from Mouse track Pad
Most of you will have a crusty crumbly mess on your Mouse track pad at some point. If it’s not just dust then you need to get rid of it! The best way to do that is with hot soapy water and a soft brush. Wet your brush with hot water and soap (your favorite mild detergent). Then take a toothbrush and gently scrub away at anything stuck to your mouse pad.
Be sure not to use too much force as you don’t want to damage your pad, but also be mindful that these things won’t come off easily! The best thing is if you can remove them before they harden completely as then it is easier to lift off whatever has become attached (for example…yesterday’s lunch!). Once all that gross stuff is gone you should give your mouse pad a good rinse under warm running water. Make sure it dries completely before using again!
4) Remove any liquid spills with paper towels
Moisture is one of a mousepad’s worst enemies. To remove liquid, first use several layers of paper towels to absorb as much liquid as possible. Then, use a dry towel to dab up any residue moisture left behind. Once you’ve removed as much moisture as possible, move on to steps two and three below. Use a vacuum with a brush attachment: Using your vacuum with an attachment brush will help loosen debris that may be sticking to your mousepad.
Start at one corner of your mousepad and work in small sections. If needed, gently lift your mousepad by hand to get at hard-to-reach areas. Be sure not to apply too much pressure—you don’t want to risk tearing or ripping your pad! Wash it in warm water: You can wash most mousepads in warm water using mild soap or detergent. To prevent shrinkage or damage from washing machine spin cycles, lay them flat (as opposed to folding them) before placing them in a washing machine.
5) Don’t use harsh chemicals on your
If you’re like most people, you probably use your Mouse track pad every day without giving it much thought, until it becomes too dirty to look at. While cleaning your mousepad won’t take long. And there are several common mistakes that could be making it look worse than ever before. In order to make sure your mousepad stays clean and looking nice. So be sure to avoid these 10 common mousepad cleaning mistakes!
1) Mouse track pad Prevent stains
You can protect your Mouse track pad from spills by using a sleeve or protector. If you don’t have one, you can easily make your own from materials found in most homes. Cut open an old pillowcase and lay it flat with one end touching a wall. And another touching a corner of your desk. Place your mouse pad on top of it, so that when you turn it over. There’s about 3/4 inch to 1 inch of pillowcase sticking out beyond where your mouse pad ends. This is where liquid will collect if you spill anything on it. But since there’s more room than before, less of it will stain or leak through onto your computer. (Just be sure to flip it back once you’re done.)
As far as stains go, all you need is water and soap. Don’t use harsh chemicals like bleach or ammonia unless they’re specifically recommended by the manufacturer. Use a soft cloth and rub lightly at first, then scrub harder if needed until stains are gone. Once again, never scrub hard enough to cause damage! When finished, wipe down your mousepad with a damp cloth (again: no bleach. And let dry thoroughly before putting it back into use. And remember: prevention is key.
2) Touchpad clean with hot water
Hot water (or, even better, a good disinfectant) is one of your best weapons when it comes to getting rid of germs and bacteria on your Mouse track pad . Place your pad in a basin filled with water so that it covers most of its surface area, then soak it in there for 10 minutes or so. After that time has passed, you can remove your mouse pad from the water and take a clean cloth to dry off all sides. You should also shake off any excess liquid before putting it back into use. Remember: once you’ve cleaned something with hot water, you have to let it air-dry completely; otherwise, mold will form and cause an even bigger problem! So if you don’t want to keep cleaning your mouse pad regularly, try looking at anti-bacterial sprays instead.
Now spray some cleaner onto your pad’s surface—you can buy special Mouse track pad cleaners if you’d like—and wipe away anything that doesn’t belong there using a lint-free cloth. Repeat as necessary until no more dirt appears on your cloth when wiping down your pad’s surface. If you’re lucky enough to own a mechanical keyboard , make sure not to spray directly onto it; as we mentioned above, hot water is fine for most materials but might damage electronics . If yours does get wet accidentally, just dry it out quickly using another towel or hairdryer.
3) Remove gross crusty things from 10 Tips for Super Cleaning Your Mouse track pad with out damage
Most of you will have a crusty crumbly mess on your Mouse track pad at some point. If it’s not just dust then you need to get rid of it! The best way to do that is with hot soapy water and a soft brush. Wet your brush with hot water and soap (your favorite mild detergent). Then take a toothbrush and gently scrub away at anything stuck to your mouse pad.
Be sure not to use too much force as you don’t want to damage your pad, but also be mindful that these things won’t come off easily! The best thing is if you can remove them before they harden completely as then it is easier to lift off whatever has become attached (for example…yesterday’s lunch!). Once all that gross stuff is gone you should give your mouse pad a good rinse under warm running water. Make sure it dries completely before using again!
4) Remove any liquid spills with paper towels
Moisture is one of a mousepad’s worst enemies. To remove liquid, first use several layers of paper towels to absorb as much liquid as possible. Then, use a dry towel to dab up any residue moisture left behind. Once you’ve removed as much moisture as possible, move on to steps two and three below. Use a vacuum with a brush attachment: Using your vacuum with an attachment brush will help loosen debris that may be sticking to your mousepad.
Start at one corner of your mousepad and work in small sections. If needed, gently lift your mousepad by hand to get at hard-to-reach areas. Be sure not to apply too much pressure—you don’t want to risk tearing or ripping your pad! Wash it in warm water: You can wash most mousepads in warm water using mild soap or detergent. To prevent shrinkage or damage from washing machine spin cycles, lay them flat (as opposed to folding them) before placing them in a washing machine.
5) Don’t use harsh chemicals on your Mouse track pad
Before you clean your mousepad, check to see if it’s got a sticker on it. If so, make sure you don’t use anything that could ruin those labels. Some products may also say they’re safe to use on silicone or plastic surfaces, but not both—be sure to read any directions first! It’s always better to be safe than sorry when it comes to damaging your tech gear.
Plus, many of these products have chemicals that may smell bad and could leave residue behind even after cleaning. Try using mild soap and water instead; even hot water alone can do wonders for breaking down dirt. If all else fails, try rubbing alcohol—it’ll get rid of smells too. Just remember: be gentle with your mousepad and don’t scrub too hard! You might end up making things worse. When in doubt, ask an expert before proceeding with any type of cleaning process on your mousepad.
6) Let it dry naturally in open air
A mouse pad is a piece of equipment you use every day, so it’s only natural that it gets dirty. Luckily, cleaning your mouse pad is easy. The first step to keeping your desk clean and free of dust buildup is to keep your mouse pad clean and dry. Instead of tossing your old mouse pad in with your laundry (which will trap dirt in the fabric), leave it outside or lay it out on a towel to air dry after washing. You can also gently wipe off any surface grime and sweat from working on long projects by hand. This might seem like an unglamorous way to go about cleaning, but it actually works quite well! Most importantly: resist using chemicals, harsh cleaners or bleach as they can do more harm than good if not handled properly!
7) Store it upside down, instead of flat
While you want to air out your mouse pad every once in a while, storing it upside down means that crumbs and dust won’t end up in between its cracks and crevices. Put it in a sealable bag while you’re not using it: This will keep dirt off of your mouse pad when you have to put it away or if you’re transporting it somewhere. Keep food away from your computer: Any crumbs or liquids around or on your computer can result in potential damage down the road, and a dirty mouse pad isn’t going to help matters either.
8) Change the angle of your mouse when using it on a dirty mouse pad
If you’re finding that your mouse is doing a lot of slipping around, chances are it’s because of build-up on your mouse pad. The best way to keep your gaming gear clean is by changing how you hold it when in use. Rather than holding your mouse completely flat over your pad, try angling it upward slightly so that only one side of its feet touches down on any given point—this will allow you to better grip control over where it goes and prevent slippage. Just make sure to angle up from an angle, as having both sides touch at once will simply put more pressure on already contaminated parts and make things worse!
9) Use wipes to clean daily, if possible.
This can mean a lot of things, but in general, I just mean that you should try to use cloth wipes (something like Clorox Disinfecting Wipes) to clean your mouse every day. This doesn’t really work if you have a laptop. Because most of those mice are too small to wipe down properly with a cloth. However, if you do happen to be rocking one of those fancy wireless Bluetooth mice or something like that. Then by all means go ahead and grab a few wipes from under your sink each night. Using daily wipes will help keep your mouse cleaner and fresher-smelling than it would otherwise be if you were just using water on it regularly.
10) If you still have stains after following these steps use rubbing alcohol (diluted).
If all else fails, a 50/50 mixture of rubbing alcohol and water will break down most stains. Don’t rub too hard, just let it sit and it should come off. (This step is not necessary). If you still have trouble with your mouse pad, there are a variety of cleaners specifically designed to clean mouse pads on eBay or Amazon. Be sure to follow directions closely! And be careful – some chemicals will eat through your mouse pad.
Before you clean your mousepad, check to see if it’s got a sticker on it. If so, make sure you don’t use anything that could ruin those labels. Some products may also say they’re safe to use on silicone or plastic surfaces, but not both—be sure to read any directions first! It’s always better to be safe than sorry when it comes to damaging your tech gear.
Plus, many of these products have chemicals that may smell bad and could leave residue behind even after cleaning. Try using mild soap and water instead; even hot water alone can do wonders for breaking down dirt. If all else fails, try rubbing alcohol—it’ll get rid of smells too. Just remember: be gentle with your mousepad and don’t scrub too hard! You might end up making things worse. When in doubt, ask an expert before proceeding with any type of cleaning process on your mousepad.
6) Let it dry naturally in open air
A mouse pad is a piece of equipment you use every day, so it’s only natural that it gets dirty. Luckily, cleaning your mouse pad is easy. The first step to keeping your desk clean and free of dust buildup is to keep your mouse pad clean and dry. Instead of tossing your old mouse pad in with your laundry (which will trap dirt in the fabric), leave it outside or lay it out on a towel to air dry after washing. You can also gently wipe off any surface grime and sweat from working on long projects by hand. This might seem like an unglamorous way to go about cleaning, but it actually works quite well! Most importantly: resist using chemicals, harsh cleaners or bleach as they can do more harm than good if not handled properly!
7) Store it upside down, instead of flat
While you want to air out your mouse pad every once in a while, storing it upside down means that crumbs and dust won’t end up in between its cracks and crevices. Put it in a sealable bag while you’re not using it: This will keep dirt off of your mouse pad when you have to put it away or if you’re transporting it somewhere. Keep food away from your computer: Any crumbs or liquids around or on your computer can result in potential damage down the road, and a dirty mouse pad isn’t going to help matters either.
8) Change the angle of your mouse when using it on a dirty mouse pad
If you’re finding that your mouse is doing a lot of slipping around, chances are it’s because of build-up on your mouse pad. The best way to keep your gaming gear clean is by changing how you hold it when in use. Rather than holding your mouse completely flat over your pad, try angling it upward slightly so that only one side of its feet touches down on any given point—this will allow you to better grip control over where it goes and prevent slippage. Just make sure to angle up from an angle, as having both sides touch at once will simply put more pressure on already contaminated parts and make things worse!
9) Use wipes to clean daily, if possible.
This can mean a lot of things, but in general, I just mean that you should try to use cloth wipes (something like Clorox Disinfecting Wipes) to clean your mouse every day. This doesn’t really work if you have a laptop. Because most of those mice are too small to wipe down properly with a cloth. However, if you do happen to be rocking one of those fancy wireless Bluetooth mice or something like that. Then by all means go ahead and grab a few wipes from under your sink each night. Using daily wipes will help keep your mouse cleaner and fresher-smelling than it would otherwise be if you were just using water on it regularly.
10) If you still have stains after following these steps use rubbing alcohol (diluted).
If all else fails, a 50/50 mixture of rubbing alcohol and water will break down most stains. Don’t rub too hard, just let it sit and it should come off. (This step is not necessary). If you still have trouble with your mouse pad, there are a variety of cleaners specifically designed to clean mouse pads on eBay or Amazon. Be sure to follow directions closely! And be careful – some chemicals will eat through your mouse pad.
